WaterFall

The Power You Need for the Ultimate Backyard Waterfall

The Jandy® WaterFall pump is ideally suited for custom natural waterfalls, spillover grottoes, and other special water features.

Find a Dealer

The Power You Need for the Ultimate Backyard Waterfall

The Jandy® WaterFall pump is ideally suited for custom natural waterfalls, spillover grottoes, and other special water features. It operates in high-flow, low pressure applications using less energy than standard pumps and runs 60% quieter.

Features

  • Ergonomic cam-lock lid with easy-to-read alignment indicators
  • Operates 60% quieter and uses less energy than standard pool pumps

Technical Details

  • High-flow, low head pump
  • Ergonomic cam-lock lid with easy aligning indicators
  • Comes complete with 2 1/2" x 3" quick-connect unions
  • Available in two sizes: 125 and 185 GPM

Specifications

Model HP Voltage Amps Pipe Size Carton Weight Overall Length ‘A’
SWF125 .75 230/115 4.8/9.6 2.5"-3" 48 lbs 33.25"
SWF185 1.0 230/115 6.0/12.0 2.5"-3" 56 lbs 34.5"

Models

Models Description
SWF125 Jandy Pro Series Stealth Waterfall Low Head Pump, 230/115 VAC, 125 GPM
SWF185 Jandy Pro Series Stealth Waterfall Low Head Pump, 230/115 VAC, Up To 185 GPM

Parts Breakout Diagram

Jandy Pumps by Zodiac

WaterFall Pump Parts List

Launch our online catalog viewer to review breakout diagrams and part numbers.

Learn More

Accessories

Models Description  
SEAQL1001 Jandy Pro Series Sweep Elblow Aqualink Temp
SEFL1002 Jandy Pro Series Sweep Elbow Flowlink

Frequently Asked Questions

Click a frequently asked question below to see the answer.

Air leaks are still present.

1 Check the suction side piping union. While the pump is running, try to tighten the union. If this does not stop the air leak, turn off the pump. Loosen both unions and slide the pump out of the way. Remove, clean and re-install both union o-rings.
2. Reposition the pump next to the piping and secure the union nuts to the pump. With clean union o-rings, hand tightening of the unions should create a seal. If the unions still do not seal, gently tighten with a large pair of tongue and groove pliers. DO NOT OVER-TIGHTEN.

Bubbles present in the pump basket.

1. Air in system. Check the pool or spa water level to ensure it is at the proper level and that air is not being drawn into the suction plumbing.
2. If the water is at normal level, turn off the pump. Remove the lid and check for debris around the lid o-ring seat, as this will cause air leaks in the system.
3. Clean the lid o-ring and put the lid back in place.
4. Hand tighten the lid to make an air tight seal.
5. Do not use any tools to tighten the lid. Turn the pump back on.

The cleaning/circulating system is not operating correctly.


1. Verify that the skimmer baskets, pump basket and other screens are clean. Clean as necessary.
2. Check filter and clean as necessary.
3. Check valve positions. Adjust as necessary. Note: Multiple pieces of equipment operating at one time (for example, waterfalls, spa jets, and surface returns) will affect the cleaning system and may prevent it from working properly.
4. Check the cleaning system manual to ensure that the system is adjusted according to the manufacturer's recommendations.

The pump gets hot and shuts off periodically.

1. Ensure that there is adequate room around the motor to circulate air and keep the motor cool.
2. Have a qualified electrician check for loose connections and check the voltage at the pump motor while it is in operation. The voltage must be within 10% of the motors data plate rating. If the voltage is not within 10%, contact a qualified electrician and/or the local power service provider.

The pump is leaking water between the motor and pump body.

This is caused by a damaged or failed mechanical seal. Replace the seal. See the "Mechanical Seal Replacement" portion of the manual.

There is no air in the system, but the pressure is still low.

1. It is possible that debris is caught in the impeller. The pump impeller moves the water, and the vanes in the impeller can become blocked with debris. See the "Blocked Impeller" portion of your manual for more information.

There is no debris blocking the impeller and the pressure is still low.

1. The pump impeller and diffuser are showing signs of normal wear. Have a qualified service technician check the impeller and diffuser and replace as necessary.
2. If the pump is part of a relatively new installation, it could be an electrical problem. Contact a qualified service technician. Have the technician check for loose electrical connections and check the voltage at the pump motor while in operation. The voltage must be within 10% of the motor's data plate rating. If the voltage is not within 10%, contact a qualified electrician and/or the local power service provider.
3. Pump seal is leaking air. Have a qualified service technician replace the seal.

Will I lose water if I run my pool pump on Bypass?

No, you only lose water in a pool if there is a leak, through splash out, and when you backwash.

Resources

Zodiac Pumps Family Brochure (EN)

Item #: SL6200
File Size: 4085043
Language: EN

Download View Online

Jandy WaterFall Pump Specification Sheet

Item #: SA6223
File Size: 416464
Language: EN

Download View Online

WaterFall Series Pump I/O Manual

Item #: H0321400
File Size: 3152337
Language: EN

Download View Online

Protect your warranty!

Professional Installation Required

Pro Resources

Log in to your Zodiac Premium® account now to get access to pro resources.

Log in Now